How To Remove Trex Deck Boards Without Damage

Download Article

If you notice a scratch or damaged surface area on your Trex decking, fret non! If you accept a small-scale scratch or chip, use a composite deck repair kit. If you have a larger scratch, dent, or dings, information technology is best to supercede the entire board. With a few tools, you lot tin can easily repair your deck and enjoy your patio.

ane
Purchase a repair kit if you want to easily ready your deck. To ready deck issues including minor scratches, splits, or fries, use a repair kit from a domicile supply shop. Choose a repair kit with wax applicator sticks. In add-on, you tin can purchase repair kits with scratch pads if you need to repair deep scratches.
- Choose the wax that about closely matches the color of your Trex decking.
2
Sand the scratch with a scratch repair pad or applicator tool. Apply light pressure to either the scratch pad or the applicator that came with the wax, and move the tool over the scratched spot very rapidly. Use a back and forth motility for best results. Go on sanding until the scratch is the aforementioned level every bit the residual of the lath.^[1]
- If your scratch or chip is more than ⁱ⁄₄ in (0.64 cm) deep, consider replacing the board.
Advertisement
3

Employ wax to the damaged area until it is level. Take off the tip of the wax stick, and rub information technology over the sanded expanse. Apply a thin, even layer over all of the scratches. Wax hands fills in small problem areas.^[two]
4
Rub the applicator over the wax to remove any excess. Hold the applicator in between your index finger and thumb, and lightly movement information technology dorsum and forth beyond the wax. This scrapes off any extra wax.^[3]
- Avoid pressing also difficult on the applicator, or you'll remove wax from the scratch.
Advertisement

i
Purchase a replacement lath from a Trex manufacturer or supplier. Many habitation supply stores sell Trex decking, and yous can as well buy information technology directly from the manufacturer. Ensure your new lath matches the size and colour of your existing decking.
- You lot can search online to find a Trex manufacturer near you.
2
Utilize a pencil to mark the board in iii equal intervals. Wait at your board, and divide it vertically into approximately 3 equal parts. Draw a vertical line running the length of the board so it'south divided in thirds.^[4]
- This fashion, you can easily separate your board.
3
Make ii parallel cuts with a mitt saw to remove the middle of the board. Use a round paw saw to hands make your cuts. Position the saw at the start of 1 of your lines, and make a direct cut down the board post-obit the line. Then, do the same thing for your other line.^[five]
- Make your cuts as directly equally possible and then the lines are parallel.
- Continue your fingers away from the blade at all times to forestall injury.
- Wear safe goggles to protect your eyes.
iv
Remove the heart piece of woods from the rest of the board. Using your easily, lift upwardly on the board from 1 side, and have it out of its spot. Place the board down on the neck adjacent to you lot.^[vi]
- The board should hands come up out from the residue with minimal force.
5
Take out the other two remaining side pieces of the board from the tabs. Once you remove the piece in the center, pick up the other two pieces of the board. The boards are secured by small, metallic tabs underneath. To remove the boards, merely lift upward on them so they separate from the tabs. Identify them all next to each other out of the manner until you can dispose of them.^[vii]
- Throw your Trex pieces away when it is trash dark.
- To protect your hands, wear safe gloves as you lot practice this. That manner, they cannot get scraped.
6
Hammer the tabs on the sides and then the spiral heads only prove on one side. There are several small metal tabs that held the old board in identify. After the old lath is out of the way, utilise a hammer to push the metal tabs downwards. Hit the tabs with moderate strength nearly 3-five times until they are flush with the board next to it. This gets the tabs out of the style, so you tin hands fit the new board in place.^[8]
- If y'all are having trouble, utilise more forcefulness every bit y'all hit the tabs.
7

Place a new board on the remaining tabs. Once the tabs are hammered down, simply lay down the new lath in identify of the quondam one. Make sure y'all use the same size and color of Trex decking.^[9]
8
Utilise a pry bar to put the new board into place. To secure the board into its spot, put the tip if the pry bar in between the new lath and the board next to information technology, and pull back on the pry bar with low-cal pressure.^[10]
- Practise this for both sides to wedge the board into place.
nine
Drill screws into the new board and the base. Once you lot have the board in position, put the spiral in between the new board and its next lath. So, place a screw at a 45-degree angle at the side of the lath. Use a drill to secure the nail in place. Drill 1 nail into the left and right side at both the peak and bottom.^[xi]
- This screws secure the lath in identify.
Advertisement

Enquire a Question

200 characters left

Include your email accost to get a message when this question is answered.

Submit

Things You lot'll Need

Trex decking
Composite deck repair kit

Trex decking
Pencil
Safe glasses
Gloves
Circular hand saw
Hammer
New board
Pry bar
Drill
Screw

Before you work on your deck, read the specific manufacturer instructions regarding repairs. That way, you do non damage your deck.

Thanks for submitting a tip for review!

Advertizing

Nigh This Commodity

Article Summary X

Don't fret if your Trex decking is damaged, since you can fix pocket-size chips or replace a board if yous need to. For minor scratches, splits, or chips, buy a repair kit from a home supply store. These come with scratch pads and wax, only you can buy the products separately too. But brand sure you get the right colored wax for your deck. Once you've got your supplies, sand the damaged area with a scratch pad, apply wax to make full in the gap, then sand it again to brand it level. Yous tin too buy replacement boards if 1 of your boards is beyond repair. First, cut the board into thirds with a saw. Then, utilise the middle piece to replace your damaged lath and secure it with a crowbar and drill. For more tips, including how to remove damaged Trex boards, read on!

Did this summary assistance yous?

Thanks to all authors for creating a page that has been read 44,763 times.

Did this article help you?